Comparison


Darkglass Microtubes X Ultra Bass Preamp Pedal with Variable Lowpass/Highpass Filters, 6-band Graphic EQ
Code: MICROTUBES X ULTRA
Brand: Darkglass
Categories: Bass Guitar Pedals & Effects , Bass Graphic EQ
The Microtubes X Ultra greatly expands on the already immense versatility of the Microtubes X7. Featuring all the great controls that its predecessor has that allows users to select exactly what frequencies they want to compress and saturate for the low and treble respectively, but with four major additions providing an additional layer of flexibility, while maintaining the same compact footprint, making it an extremely complete tool for the modern bassist.
Microtubes X Ultra Bass Preamp Pedal With Variable Lowpass/Highpass Filters, 6-band Graphic EQ from Darkglass is 100% original and brand new. We, at Melody House take pride in our after sales service and support. For further details on the Microtubes X Ultra Bass Preamp Pedal With Variable Lowpass/Highpass Filters, 6-band Graphic EQ, Darkglass, simply write to us to consult an expert or order online and we will take care of the rest. Happy Shopping!
Low Comp | Controls compression amount for the low band. Both threshold and makeup gain are controlled to maintain a constant level. This control is also used to control the compression amount when the compressor is enabled for clean signal in Darkglass Su |
Low Level | Sets the output volume of the low-pass signal. |
Low Pass Frequency | Controls the cut-off frequency to be mixed back to the high-pass side. Ranging from 50Hz (for only sub-bass) and 500Hz to preserve some clean mids. |
High Level | Sets the output volume of the distorted high-pass signal. |
High Drive | Sets the amount of distortion for the high pass side. |
High Pass Frequency | Controls the cutoff frequency to be distorted, ranging from 100Hz (for thicker, fuzzier saturation) or 1kHz for ultra-sharp definition. |
Master | +-12 dB. Sets the overall volume of the unit. |
Low shelf | +-12 dB @ 80 Hz. |
250 Hz / 500 Hz / 1,5 kHz / 3 kHz | +-12dB. |
High shelf | +-12 dB @ 5 kHz. |
Direct Output | Balanced XLR output for connecting the pedal to a microphone preamp, PA system, etc. |
Ground lift | Disconnects the signal ground on the Direct Output to break any ground loops. Set this switch to either position that has less noise. The switch does not affect the ¼” output. |
Cab Sim | Toggle the cabinet simulation on/off on the Direct Output. This switch completely bypasses all digital circuits and allows you to get a zero latency signal when needed. |

Marshall DSL100HR 100 Watt Tube Guitar Amplifier Head with 2 Channels (Each with 2 Modes)
Used by history's most iconic musicians, everyone dreams of owning a high-powered Marshall amplifier stack. To fulfill the dreams of more and more guitar players, Marshall released the DSL series. All-tube, all-original Marshall amps delivering that legendary Marshall tone; the standard by which all other amplifiers are judged.
The Marshall DSL100HR is a 100-watt all-tube head. With four 12AX7 (ECC83) tubes in the preamp and four EL34 tubes in power section, expect clear, rounded clean tones, and of course, roaring and screaming rock distortion as we all know it. Speaking of distortion, you have three gain modes to choose from: Crunch Mode for good ol' rock n' roll, OD1 for arena rock, and (OD2) for that saturated heavy metal sound.
On top of its very responsive 3-band EQ, the DSL100 also has Resonance and Presence controls to fine-tune the low end resonance as well as the upper mids and treble. There is also a Tone Shift button, which when engaged, reconfigures the pre-amp mid frequencies making DSL ideal for contemporary metal tones,especially when combined with higher gain settings.
For added flexibility, the DSL100 also has onboard digital Reverb for added depth, as well as an effects loop to integrate your pedal setup. You can also connect an external MIDI controller (sold separately) to allow remote control of some front panel functions. For studio works or rehearsals, you can also bring the output power down to a more manageable 50 watts.
For just about half the price of its other Marshall brothers, the DSL100HR Amp, owning a 100-watt Marshall is no longer a distant dream for the working guitarist.
DSL100HR 100 Watt Tube Guitar Amplifier Head With 2 Channels (Each With 2 Modes) from Marshall is 100% original and brand new. We, at Melody House take pride in our after sales service and support. For further details on the DSL100HR 100 Watt Tube Guitar Amplifier Head With 2 Channels (Each With 2 Modes), Marshall, simply write to us to consult an expert or order online and we will take care of the rest. Happy Shopping!
Type | Head |
Wattage | 100 / 50 watts (switchable) |
Channels | 2 (Classic and Ultra), each with 2 modes |
Tubes | 4 x ECC83 (preamp), 4 x EL34 (power amp) |
Controls | Loop On/Off, Master Volume 2, Master Volume 1, Master Select, Reverb x 2 (for Ultra and Classic), Resonance, Presence, Tone Shift, Bass, Middle, Treble, OD1/OD2 switch, Volume & Gain (Ultra), Volume & Gain (Classic), Clean/Crunch switch |
Output Impedance | 4, 8, and 16 ohms |
Effects Loop | Yes |
Inputs | Guitar input (1/4"), Audio input (1/8"), MIDI in, Footswitch in |
Outputs | 1/4" Speaker Outs (1 x 16 ohms, 1 x 8 / 2 x 16 ohms, 1 x 4 ohms / 2 x 8 ohms), 1/4" Emulated Line Out |
Dimensions | (HxWxD) 10.8 x 29.1 x 9.5 inches |
Weight | 24.2 kg |
Included | 2-button footswitch (PEDL-90012) |